Avalon Pellet Stove Manual [Step by Step Guide]

You are probably having problems understanding your Avalon pellet stove’s functionality. It can be frustrating if you can’t operate your device in the perfect way. And the confusing manuals don’t always help. This is why we have simplified the instructions for you.

Here in this article, you will get to know about 4 things you can learn from the Avalon pellet stove manual. Our discussion will help you to use your Avalon pellet stove as simply as possible. So without further ado, let’s get started.

4 Things To Learn From Avalon Pellet Stove Manual 

Using and maintaining an Avalon pellet stove can be difficult. But, the Avalon pellet stove manual can make it easy for you. The instructions in the manual will certainly help you keep your pellet stove in sound condition

Most common pellet stove manuals such as Avalon Astoria pellet stove manual and the Avalon Newport pellet stove manual boil down to 4 main points. Here are the 5 things that you can learn from the Avalon pellet stove manual:

1. How to operate the Avalon pellet stove

2. How to clean Avalon pellet stove 

3. Avalon pellet stove indication lights & solutions

4. Optional parts of Avalon Pellets stove parts and their usage

Learning these things will enable you to handle your Avalon pellet stove with more efficiency.

Let’s start with operating the device.

5 Steps To Operate the Avalon Pellet Stove

Suppose you have seen an Avalon 900 ps pellet stove for sale and you have bought it for your living room. A mechanic will be able to set up your fireplace. But, what will you do after that?

If you don’t have any idea about how to operate this device, the Avalon pellet stove control board will seem confusing. Without proper guidance, the Avalon pellet stove parts and the Avalon pellet stove inserts will make no sense to you at all. 

This is why when you find an Avalon pellet stove for sale, you shouldn’t just buy it, you have to learn how it operates as well. Here are 5 steps to operate the Avalon pellet stove with the highest efficiency.

Step 1: Starting Up

Firstly, plug in the power switch and wait for the operating lights to turn on. Once the power switch is on, press the “START” button. This will turn on the heater and the fan. (The heater can take up to 15 minutes to start). Simply put, this will turn on your stove.

Step 2: Adjust The Burner

After starting up, allow your heater to run for 15 minutes. Now, adjust the burn rate dial according to the level of heat you need. If you set the burn rate to a high setting the pellets will feed into the firepot faster. This will eventually generate more heat. 

And in case you want low heat, adjust the burn rate dial to a lower level. The pellet quality affects the amount of heat as well.

Step 3: Adjust The Air Control

Air control maintains the amount of air that enters the firepot. The air that enters the firepot greatly affects the fire. More airflow causes more fire. This is why it’s important to adjust the air control perfectly. There are mainly 3 ways to adjust the air control:

  • When the pellets are not moving and the flame is dark orange and has black tips – Pull the air control out 1/2” 
  • When the pellets are vigorously moving and burning pellets are jumping out of the firepot – Push the air control in 1/2”
  • When the pellets are slightly moving and the flame is bright yellow and jagged – Don’t do anything. The air control is perfectly adjusted 

The label on the air control will show three colors. You can determine the flame condition from these indications.

These colors mean:

  • Red – High
  • Orange – Medium 
  • Yellow – Low

Step 4: Adjust The Fan Dial

The fan dial is an important part of the pellet stove. The fan determines how much heated air will blow out of the heat exchange tubes located above the door. So, set the fan dial following the burn rate you want. 

The higher you will set the fan, the more heat you will get. And this means that the pellets will burn faster as well.

Step 5: Turning It Off

You should never keep your pellet stove turned on when you don’t need it. It will not only cost you extra bucks but damage your device as well. To turn off the pellet stove, simply switch the power button to the “OFF” point and this will turn off the device completely.

However, there is one thing to keep in mind. Never unplug the heater to turn it off. Directly unplugging the device can cause smoke to enter your room. You have to agree that these instructions are fairly simple. You just have to use a certain dial and set it perfectly. Everything can get easier if you are aware of the proper methods.

8 Steps To Clean Avalon Pellet Stove Perfectly

Avalon pellet stoves can attract dirt quite easily. Dirt and debris can badly affect the overall performance of your Avalon pellet stove. The burner may not generate perfect flame, the Avalon pellet stove blower motor may not work, and many more things can happen.

This is why it’s important to know how to clean the Avalon pellet stove. As the Avalon pellet stove is composed of lots of parts and inserts, you have to deal with each part individually to thoroughly clean the whole device. 

Avalon pellet stove has lots of parts and inserts. This is why when it comes to cleaning, you have to deal with each part individually. So, you have to deal with each part individually while cleaning. 

To make the cleaning process easy for you, we have a clear set of instructions here. These methods show you how you can clean each part of your stove to make the whole device free of dirt and debris. If you follow these instructions, you will be able to properly clean your Avalon pellet stove in less than 10 steps.

You will be capable of cleaning your Avalon pellet stove perfectly in less than 10 steps following our simple instructions. Here’s how:

Step 1: Cleaning The Ashpan

You should check the ashpan every time you use the stove. First, look through the window to check if fly ash has built upon the ashpan. Turn the heater off in case you notice 1” of ash accumulated on the pan. After turning the heater off, wait for it to cool down. And then empty the ashpan. 

To do this, you have to turn both of the handles that are located under the ash lip. Give it a 1/4 turn to keep the knob lines pointing upwards. This will allow you to pull the ash pan out. After pulling out the ashpan, dispose of the ashes somewhere safe. Finally, wipe the ash pan with a clean piece of cloth before placing it back in.

Step 2: Cleaning The Heat Exchanger Tubes 

It is recommended that you clean the heat exchanger tubes at least once a week. It’s the part of the stove that allows better heat transfer. If you don’t keep it clean, the device may not provide sufficient heat. Cleaning the heat exchanger tubes is fairly simple. Follow these point’s to clean the tubes:

  • Close the door
  • Locate the built-in cleaner. You will find it above the door
  • Push the built-in cleaner back and forth a couple of times
  • Use a tool or wear gloves to do this because the parts of stoves are usually hot
  • If you see fly ash falling from the roof of the firebox, keep pushing the built-in cleaner back and forth
  • Stop once there is nothing coming out of the heat exchanger tube
  • Clean off the ashes that fell from the heat exchanger tube

And after following these steps, you have perfectly cleaned the heat exchanger tube. 

Step 3: Cleaning The Firebox and Glass

You should clean the firebox at least once a week. The glass should be cleaned at the same time as well. It is convenient to clean both at the same time because of their positioning. Do the following things to clean the firebox:

  • Dispose of the fly ash from around the firepot
  • Remove the log set and brush it clean 
  • Brush off all the fly ash from the surface of firebrick refractory 
  • Brush off the fly ash from the wall of the firebox as well
  • After brushing it all off, clear out the ash buildup from the ash pan  

This is how you will be able to properly clean the firebox. To clean the glass, simply just wipe it off with a non-abrasive glass cleaner. This is the best way to clean the glass of your Avalon pellet stove.

Step 4: Cleaning The Ash Traps

The ash trap catches fly ash before the exhaust gas exits the firebox. It’s important to clean the ash trap so that more pellet ashes can build up. Here’s how to clean the ash trap:

  • To clean the ash trap, you have to remove the firepot and the holder first. And then, empty the ashpan.
  • There are four ash trap doors on the bottom of the firebox. Remove these trap doors by swinging them out and sliding them up and out. This way you will be able to clean the fly ashes behind the door.
  • You can use a vacuum cleaner or a normal brush to clean off the fly ash from behind the trap doors.
  • Reinstall the trap doors properly by laying them flat against the surrounding metal

After doing all this, you will have properly cleaned the ash trap of your pellet stove. 

Step 5: Cleaning The Hopper and The Auger Tube

Whether you should clean the hopper and the auger tube depends on the number of pellets you have used so far. Clean the hopper and the auger tube after every 1,000 lbs of pellets your stove burns. You have to keep track of the weight in this situation. 

If there is more than 1/2 cup of sawdust, then you will have to clean the hopper and the auger tube for every 500 lbs of pellets you burn. Cleaning these two parts can be very easy. You just need a vacuum cleaner for this task. Vacuum the hopper area and the exposed part of the auger tube. 

Try to reach the interior of the auger using a vacuum cleaner Extention. After you have cleared out all the dirt and debris, your hopper and auger tube is good to go again. 

Step 6: Cleaning the Exhaust Ducts

The exhaust ducts are very important for a pellet stove. Its purpose is to transfer heat. The exhaust ducts are located inside the firebox and they need to clean after burning 6,000 lbs. of pellets. Otherwise, it will get damaged and you have to install a new duct. To clean the exhaust ducts, you have to:

  • Remove the ash trap doors
  • Remove the firebrick refractory. It will expose two clean-outs on the back wall of the firebox
  • Remove these clean-outs using a screwdriver
  • Tap against the exhaust ducts and remove the loose fly ash
  • Brush away any sort of fly ash or built-up soot
  • Use a wire to clean the inside of the exhaust ducts
  • After soot and fly ash accumulates on the ashtray, clean it all using a vacuum cleaner
  • Attach new clean-outs, firepot holder, firebrick refractory,and exhaust ducts after you are done

And once you have done it all, the exhaust ducts of your Avalon pellet stove will be perfectly clean.

Step 7: Cleaning the Convection Blower

The significance of the convection blower is that it pushes air through the heat exchanger tubes. It basically transfers heat from the firebox to the room. This easily collects dirt and requires thorough cleaning. If you don’t clean regularly, the blower may not work finally.

Here’s what you can do to clean the convection blower properly within minutes.

  • Open the left side panel
  • Disconnect the powers of the convection blower
  • Take a 7/16 inch socket wrench
  • Use the wrench to remove the one nut located on the top of the blower
  • Now, pull out the convection blower
  • Clean off any dirt you can see
  • Tap the blower to dislocate dirt from the inside
  • Shake the blower to remove dirt from the inside
  • Inspect the impeller blade and brush off the dirt
  • Vacuum for the final touch
  • Reassemble the convection blower reversing the detaching method   

Now, you should have a perfectly cleaned convection blower and a perfect stream of heat.

Step 8: Cleaning the Exhaust Blower

The exhaust blower is as important as the convection blower. It pulls in combustion air through the heater and pushes the flue gas through the pellet vent. In this process, the blower collects lots of dirt. To ensure proper flow of heat, the exhaust blower should be cleaned after every 3 tons of fuel usage. To clean the exhaust blower,

  • Unplug the heater
  • Disconnect the powers leading to the exhaust blower
  • Take a 3/8 inch nut driver
  • Remove the four mounting nuts on the exhaust blower.

Three of these nuts are located on the top of the blower and another one can be found on the lower left. There is a hole in the base to access this nut

  • Remove the insulation that surrounds the exhaust blower.
  • To do it, tilt the blower outwards
  • Inspect the gasket and the insulating. Replace the gasket, if needed
  • Use a vacuum cleaner to clean the exhaust blower
  • Reverse the detaching method to reassemble the exhaust blower

These 8 simple steps can help you to clean the most important part of your Avalon pellet stove. And if you have strictly maintained the 8 steps we have just discussed, you will have a clean pellet stove. Your patience and effort can make your device good as new.

3 Indication Lights, Their Meaning  & Solutions

The Avalon pellet stove has built-in indicator lights. These lights refer to different types of problems your pellet stove is most likely to have. It goes without saying that these lights can be very helpful, but only if you are aware of what they mean. Take a look at the following discussion to understand these lights and solve the issues:

Light 2: Green

This indicator light means:

  • Heavy ash has built up in the exhaust duct
  • Heavy ash has built up in the exhaust housing
  • Heavy ash has built up in the plugged tubing
  • Heavy ash has built up in the vent

So when this indicator comes up what you need to do is:

  • Clean the firebox thoroughly
  • Properly clean the exhaust housing and the tubing
  • Clean the vents
  • Inspect for any kind of ash build-up

Light 4: Yellow

The yellow indicator comes up when:

  • The heater runs out of pellets
  • The heater didn’t start correctly
  • There was a power outage
  • Restrictions were not set properly
  • Burn Pot is badly clogged
  • Air is leaking through the vent
  • Heavy ash has built up in the ashtray

In this case what you need to do is:

  • Refill the hopper
  • Restart the heater and ignite the pellets after 10 minutes
  • Restart the heater and inspect the restriction settings
  • Clean the burn pot thoroughly
  • Make sure that the door, glass, and the ash pan seal are in proper condition
  • Clean the firebox and exhaust housing

Light 6: Red

The red light indicates to:

  • Electrical input error such as voltage or MHz fluctuation
  • AMP deficiency
  • Overheated components
  • Faulty wiring

In this case, you have to do the following:

  • Unplug the heater and plug it back in to restart the circuit board
  • Thoroughly clean the vent and heater
  • Call in a professional to fix the wiring

The indicator lights of the Avalon pellet stove can save you from a lot of trouble. So keep the meaning of these indications in mind and protect your pellet stove from potential harm. But when you face any problem out of these, you should read the ultimate troubleshooting guide of Avalon pellet stove to fix the issue.

3 Optional Equipment You Can Use With Avalon Pellet Stove

Avalon pellet stove functions with the help of different parts. These parts co-operate to maintain the stove’s functionality. Adding more parts can increase the efficiency of the stove. Take a look at the 3 best optional equipment you can use with an Avalon pellet stove.

1. Ceramic Log Set:

Ceramic logs are a kind of wood replacement. Ceramic logs are used in pellet heaters so that the stove appears as a wood stove. Its purpose is to give the stove an aesthetic look. The ceramic logs are usually placed on a log holder in front of the firebox. 

After placing the ceramic log, check the flame. If the flames are too sooty, readjust the logs. This way the flame will be stable.

2. Stove Legs:

Stove legs are used to elevate the stove. There are three types of stove legs available; cast brass, cast black, and black steel. To install the stove legs you have to:

  • Raise the stove first by inserting some pieces of wood in the middle of the stove
  • Position the stove legs aligned to the hole in the stove
  • Now, use a wrench to tighten the connection of the stove legs with the stove’s bottom
  • Make sure the legs are strongly attached to the stove 

And now, you have perfectly elevated your pellet stove from the ground. You can raise your stove up to 8” with these stands.

3. Pedestal:

The pedestal works as a divider to prevent your stove from directly touching the floor. To use the pedestal you have to place the pedestal first. And then you have to lift the stove and place it on the pedestal. 

After positioning the stove, use a 9/16” socket wrench to attach it to the pedestal. Your pellet stove will work just fine without this equipment. But you can use these elements to upgrade your pellet stoves’ efficiency.

FAQ:

1. Why does my pellet stove keep shutting off?

Ans: Your pellet stove may keep shutting off due to one or more of the following conditions. 

  1. Incorrect feeding of pellets to auger
  2. Insufficient air supply 
  3. Faulty parts 
  4. Clogged dirt in the pipe

2. How do you adjust the airflow on a pellet stove?

Ans: To adjust the airflow on a pellet stove, you have to press the dedicated button or handle. If the pellets are burning too quickly, then keep pressing until it burns normally.

3. Why is my pellet stove not blowing heat?

Ans: Your pellet stove can produce low flame and not blow heat if you add too many pellets in the stove to make space for enough airflow.

4. How do I circulate the heat from my pellet stove?

Ans: To circulate heat from your pellet stove, you have to:

  1. Turn on the ceiling fan
  2. Make sure it runs clockwise 
  3. Ensure that it runs at the slowest speed.

5. How do I get more heat out of my pellet stove?

Ans: To get more heat out of your pellet stove, you have to do the following:

  1. Make sure there is enough feeding of pellets
  2. Clean the stove once a week at least
  3.  Clean fans to ensure sufficient  air supply 
  4. Check if the ashes are built up. 

6. What is the best setting for a pellet stove?

Ans: It is best to see the stove in lower heat rather than higher heat too often. Because it hampers the stove’s condition. 

7. Why does the glass on my pellet stove get dirty so fast?

Ans: The glass on your pellet stove can get dirty very fast due to insufficient airflow. Because it creates more smoke and ashes. 

8. Why is the flame so high on my pellet stove?

Ans: If the flame is too high on your pellet stove, then there may be insufficient airflow. It may be due to:

  1. Dirty fans
  2. Built-up ashes
  3. Feeding of too many pellets 

Check to see which one is the culprit and do accordingly. 

Conclusion:

The Avalon pellet stove is an impressive device. Its overall system is simple to follow and its performance is very satisfying. But, one can find it hard to maintain this pellet stove without proper guidance.

This is why we have arranged the 4 most important things you can learn from the Avalon pellet stove manual. Our discussion will certainly enable you to use your Avalon pellet stove properly. If you are left with any confusion, then do not hesitate to comment below.

Leave a Comment