Heatilator Wood Fireplace Manual [Learn A-Z for Safety]

Fireplace not only keeps us warm but also creates a positive atmosphere during heavy cold or snowfall. But installing or maintaining a fireplace can be a little bit of a confusing task. Don’t worry much about it. This article is all about your Heatilator wood fireplace manual where you’ll get all the answers to your question.

Like, how do I put up the fireplace?  Or how do I maintain it? Or perhaps you are wondering how to make your fireplace safe so that no unwanted incident occurs. You’ll find all the answers you need and much more like the Heatilator gas fireplace manual

So, without further ado let’s find out how you can operate your Heatilator wood fireplace. 

Operational Instructions For Your Fireplace

The following heatilator wood fireplace instructions would help you to know how the Heatilator wood fireplace work and allow you to operate your fireplace properly.

Safety First

Safety is the first thing you need to ensure while operating your heatilator wood fireplace. And reading the instructions manaul will help you to know the wood fireplace works and thus keep you safe.

Use Properly Seasoned Wood

Properly seasoned woods are very important for wood-burning fireplaces. They determine whether your fireplace would function properly or not. Most fireplaces face problems because of the usage of wet and unseasoned woods. 

Using perfectly seasoned wood will help your fireplace functioning properly. Wet and unseasoned woods don’t burn minutely. But what’s the exactly seasoned wood?  

Seasoned wood is the perfectly cut size, split and air dried wood.

Starting A Fire

Before starting a fire, make sure the following safety measures:

  • First, create a good draft. This will help you to prevent smoke from spillage into the room. 
  • Secondly, put away all the combustible things, gasoline or flammable vapors and liquids. These objects can easily put up a fire and create security concerns for you.

Now that we know the security precautions we should take, let’s learn about the steps that’ll help us to light up a fire.

  • The first thing you need to do is ensure that the first few fires should be moderate in size. This will allow the oils and binders to burn from the factory and the refractory to paint and cure.  Another thing to be noted is that you might smell some industrial odor. But that’s nothing to get worried about, it’s pretty normal. 
  • The next thing you need to do is use well-seasoned woods. If you don’t do this there’s always the possibility of facing issues in your fireplace. 
  • You should open the fuel damper to a fully open position.
  • After that, place twisted or crumpled pieces of paper under the fireplace grates.
  • The next step is to arrange kindling and extra pieces of wood loosely to form a kind of a then-fireplace grate. 
  • To create a draft, pre-warm the flue. It’ll help to reduce smoke spillage during startup. You should also hold a rolled piece of burning newspaper under the flue dumper for few seconds. 
  • The crumpled paper should be lit up to ignite the kindling.
  • Keep adding small pieces of wood until you get a hotbed of embers.
  • Next, add at least three or four pieces of split wood. Remember to place combustion air and flames in between them. 

Grate: Some fireplaces are designed to use grates on them. As time passes by it’ll eventually break down and needs to be replaced. Grates help to keep the longs in their right position. It also ensures proper air circulation around the fire. 

Fire Screen: The fire screen is used to control sparks. Always remember to keep it closed when the fireplace is functioning. Point to be noted, the screen will not stop burning materials from falling out. And also, the pulls or handles might be hot so be sure to be cautious before using them. 

Flue Damper: When the fireplace is working, the flue damper should be opened fully. Before igniting, look at the inside of the fireplace and carefully open the flue damper. You should keep in mind to not keep the fireplace closed as it can create lots of smoke inside your room. 

Refractory: Refractory is used to create good-looking and attractive interiors. But that’s not its only job. It also helps to contain the heat. Hairline cracks and discoloration are quite normal for a refractory and these won’t affect the safety measures of the system. It is advised to not start a fire without a refractory.

Heatilator Wood Fireplace Manual: The Main Part

Before installing your fireplace there are few things you need to take into consideration. They are as follows. 

  • The installation process must be completed by maintaining all the regional, local, and state-provided regulations. 
  • It is advised to contact local building inspectors, fire officials, and building inspectors for jurisdiction over permits and installation. 
  • Fixing a place for installing the fireplace.
  • Configuration of the vent system which will be used in the fireplace.
  • Piping of the gas supply
  • Electrical wiring needs to be secured
  • Recheck the framing and finishing details

After all of these are done now you can begin the installation process of your fireplace. You need to follow a few steps accurately in order to make the fireplace work properly. These steps are described below:

Step 1: 

First of all, unpack all the refractory and fireplace items. Be careful that you don’t break anything. 

Step 2: 

Next, take your fireplace to your desired position and place it firmly. Remember to secure enough insulation. And not to remove screws or refractory brackets from your fireplace. If you do remove the brackets remember to fill the shell holes located outside of it with screws. Side refractories can be removed by completing the same process. 

Step 3: 

Now place the fireplace on a flat surface. Don’t put it somewhere that’s not even, it might create problems during installation. 

Step 4: 

After that, it is highly advised to Install protective metal heath strips. But don’t cover them with combustion elements as they can create sparks or embers which can lead to catastrophic destruction.

Step 5: 

When these processes are done, start leveling the fireplace. It should be leveled both side-to-side and front-to-back. Then shim it with noncombustible materials accordingly. 

Step 6: 

The next step is to install the refractory and outside air kits. A point to be noted is that you must install your outer air kits on either side of the fireplace.

Step 7: 

Next, you need to install the chimney. The chimney is one of the most important parts of the fireplace. So, be very careful while installing it. One thing that needs to be noted is that the chimney may work differently than one another due to trees, rooflines, wind conditions, and buildings. 

So, you may need to adjust your chimney accordingly. The chimney’s overall height should be 20 ft and the maximum height shouldn’t cross 90 ft. Maximum unsupported chimney height above fireplace 35 ft and roof 6 ft.

Step 8: 

Next, time to do a few measurements. Determine the vertical height of the fireplace from its base to approximately the bottom of the termination cap. Then subtract the height of the fireplace assembly. It should be subtracted from the total vertical height. 

Whenever you see the chimney penetrating flooring, install a chimney firestop to stop that from happening. Remember to keep different sections of your chimneys from twisting and separating. Don’t use screws longer than 13 mm to ensure that your chimney stays straight. 

A point to be noted is that you should use only non-combustible materials below the standoffs. And when the framing is complete apply facing materials (drywall) all over your framing. 

If you find large gaps don’t worry, this could be easily solved using a fiberglass rope gasket. Again use noncombustible materials to cover the fireplace’s metal front. If you complete the steps mentioned above accordingly then congratulations. You have successfully installed your Heatilator wood fireplace.

FAQ

How does a Heatilator fireplace work?

Heatilator fireplace works with a air circulation method. First, it circulates the hot air around the firebox and then it spreads it all around the room.

Why does my Heatilator fireplace keep going out?

Dirty pilot orifice and pilot burner are the reasons behind your fireplace shutting off.

Can you manually light a Heatilator fireplace?

Yes, you can. If power is actively supplied to your fireplace, just turn the on/off switch to on mode and you’re the main burner will ignite. 

How do you light a fireplace without electricity? 

You can light your fireplace without electricity using battery backup. And in case of a standing pilot with your gas fireplace, it will light itself without electricity.

Conclusion

A fireplace can be a big headache sometimes as it contains many different and small elements. So, to install it properly just follow the instructions given in this article and you won’t face many problems. 

Leave a Comment