Your Bradford white water heater beeping is happening due to leakage in the system, empty fuel tank, overheating system, air supply blockage, and excessive pressure.
Once you handle these points, your Bradford white water heater shouldn’t bother you anymore. And in this article, we will show you just that.
So stay tuned…
Table of Contents
- 5 Reasons Bradford White Water Heater Beeping [Easy Solutions]
- 1. Leakage In The System
- 2. Empty Fuel Tank
- 3. Overheating System
- 4. Air Supply Blockage
- 5. Excessive Pressure
- FAQ:
- Why is my water heater making a high pitched noise?
- How do I reset my Bradford White water heater?
- How do you turn off a water heater alarm?
- How much does it cost to repair Bradford water heaters?
- How much does it cost to replace a Bradford White water heater?
- Final Words:
5 Reasons Bradford White Water Heater Beeping [Easy Solutions]
If you know the reasons why Bradford white water heater beeps, it will be easier for you to solve the issue. This is why we have elaborated on everything below. Take a look.
1. Leakage In The System
The most common reason why your Bradford white water heater beeps is leakage in the system. Whenever there is a leak, the heater warns you about it through beeping. The first thing you should do in this case is, take a look at the surrounding of the water heater. If the floor is wet, it is almost certain that a leak is causing the beeping.
Solution:
You can easily fix the leaks in your Bradford water heater. But for this, you have to find the point of leakage first. After that, here’s what to do:
- Turn off the water heater
- Go to the connection point or the valve that is leaking
- Take a wrench and tighten up the valves and connections
- Turn on the water heater
If the leakage remains, the issue is a leaking tank. In this case, you have no other option but to replace the heater. But consult an expert before doing so.
2. Empty Fuel Tank
Bradford white water heater runs on fuel. If this fuel runs out, the heater stops working. But before going into shut-down, the Bradford heater gives a warning about the scarcity of fuel. This beeping continues till you refuel the heater.
Solution:
Refueling the Bradford white heater is easy. Just remove the empty fuel cylinder and install a full one in its place. You will get the fuel cylinder on their website.
3. Overheating System
Depending on the weather and the placement of your Bradford white, it can overheat. And once it does, the beeping gives you a warning about it. This type of situation can lead to severe accidents. So make sure to pay attention to your furnace’s temperature.
Solution:
The solution of overheating literally demands you to do nothing. Yes, if the device is overheating, just turn it off by pressing the power button. Unplug the device from its outlet and let it cool down.
The heater should return to room temperature after 10/15 minutes. Don’t use water or anything else to cool the device down. Let it happen naturally.
4. Air Supply Blockage
Bradford white water heater beeps in case of certain error codes. So if it beeps, take a look at the LCD window on the front of the unit and see the error code there. But the device won’t beep for all error codes.
The most common error code it beeps for is Error Code 10. It means that there is a blockage in the air supply vent.
Solution:
If you notice the error code after the beeping, take a look at the air supply vent. Chances are you will find a blockage there. And in case you do, here’s how to fix it:
- Turn off the device
- Wipe the vent clean
- Use a flat thin metal to clean the obstructions stuck in the vent path
- If this doesn’t clear anything, unscrew the vent panel and clean everything thoroughly
- Put everything back on
After this, the air should be able to move freely through the vent, fixing the beeping as well.
5. Excessive Pressure
Excessive gas pressure is bad for your Bradford water heater. This is why in case there is too much gas pressure, the heater starts beeping. In this type of situation, there is usually an unusual noise coming from the gas line.
Solution:
Adjusting the gas pressure should fix the issue. Here’s how to do it:
- Make sure that the device is turned on
- Check if the fuel tank is full
- Adjust the gas valve by hand to set the pressure
Once you adjust the gas pressure perfectly, there shouldn’t be any beeping noises anymore. And just like this, you can easily fix your Bradford water heater within minutes.
FAQ:
Why is my water heater making a high pitched noise?
High incoming water pressure can be the reason behind high pitched noise coming from the water heater.
How do I reset my Bradford White water heater?
Press the red “Reset” button to reset your Bradford white water heater.
How do you turn off a water heater alarm?
You can turn off your water heater alarm just by twisting the thermostat dial to “OFF”.
How much does it cost to repair Bradford water heaters?
Fixing a Bradford water heater can cost around $150 to $750.
How much does it cost to replace a Bradford White water heater?
It can cost around $600-$800 to replace a Bradford white water heater.
Final Words:
Bradford white water heaters beeping is annoying and dangerous at the same time. This is why you should take quick action to solve this issue. Fortunately, you shouldn’t have problems with this now that you know everything. Just follow our instructions and things will be okay.
If you face further problems, you can let us know in the comment below.