Wondering how to reset the Green Mountain Grill controllers? Whether your grill won’t connect to Wi-Fi, keeps disappearing from the GMG app, gets stuck in server mode, or simply refuses to behave, you’re in the right place.
The good news is that most of these issues can be fixed in just a few minutes once you know the right method. In this guide, I’ll walk you through everything you need to know about resetting the Wi-Fi controller. So, let’s dive in!
How To Reset Green Mountain Grill [Fully Explained]
If your Green Mountain Grill suddenly disappears from the app, refuses to connect to your home network, or you find the Green Mountain Grill Wi-Fi not showing up at all, a Wi-Fi reset is often the quickest fix.
The reset process restores the Wi-Fi controller to its default settings and forces the grill back into point-to-point (P2P) mode, allowing you to reconnect and configure the wireless settings from scratch.
The exact steps depend on whether you own an older Davy Crockett or a newer Daniel Boone, Jim Bowie, or Prime-series grill. While the overall process is similar, there is one important difference in how the reset is initiated.
Step 1: Put the Grill Into Reset Mode
Start by turning the grill completely off. If you own a Daniel Boone, Jim Bowie, or newer Prime model, hold the “FOOD” button while powering the grill on.
If you have the newer Prime controllers, you’ll essentially be doing the same thing. But as there’s no “FOOD” button, you’ll be holding down the Probe 1 button. Continue holding the button for about 15 seconds. The controller will enter reset mode and begin counting upward on the display.
If you own an older Davy Crockett, the procedure is slightly different because these grills do not use the same power-switch setup. Instead of turning the grill off, unplug it from the power source first.
Then press and hold the button while plugging the grill back in. Keep holding the button until the display starts counting. Many owners get confused because older instructions reference a physical power switch that some Davy Crockett models do not have.
This is essentially the Green Mountain Grill factory reset process for the WiFi controller. If you are searching for how to factory reset Green Mountain Grill controllers, this is the procedure GMG uses to clear the wireless settings and return the board to its default state.
Step 2: Allow the Reset Sequence to Finish
Once the reset starts, leave the grill alone and let it complete the counting sequence. The display will count from 0 all the way to 999. As soon as the counting begins, you can release the button. The controller is now wiping its stored wireless settings and preparing to return to point-to-point mode.
Do not interrupt the process. If you unplug the grill or release the button before the count starts, the reset may fail, and you will have to start over. Once the display reaches 999, it should eventually display “Off.” This indicates that the WiFi board has successfully completed the reset sequence.
Many users perform this reset when the Green Mountain Grill WiFi password is not working, the app cannot find the grill, or the controller becomes stuck in server mode. A reset clears those stored network settings and gives you a clean starting point for reconnecting the grill.
Step 3: Reboot and Reconnect the Grill
After the display shows “Off,” complete the final reboot. On Daniel Boone, Jim Bowie, and most Prime models, turn the grill off and back on. On a Davy Crockett, unplug the grill once more and then plug it back in. This final power cycle allows the wireless chip to restart properly.
Give the grill roughly 30 seconds to begin broadcasting its WiFi signal again. At this point, you should see a network name beginning with “GMG” appear on your phone or tablet. The grill is now back in point-to-point mode and ready to be configured.
One thing that catches many owners off guard is that resetting the controller does not reconnect the grill to your home Wi-Fi automatically. The reset only returns the grill to its default wireless state.
Afterward, you must reconnect through the GMG app and enter your network information again. So if you are looking to fix a Green Mountain Grill Wi-Fi not showing up issue, a reset is only the first step. You will still need to complete the Wi-Fi setup process afterward.
How To Connect Green Mountain Grill To Wi-Fi
While the setup process looks intimidating at first, it is actually straightforward once you understand the different connection modes. The key is connecting to the grill directly first, then transferring it to your home Wi-Fi network.
Step 1: Connect Your Phone to the Grill in Point-to-Point Mode
Before your grill can join your home network, you must connect directly to the grill itself. This is called point-to-point (P2P) mode. When the grill is in this mode, it broadcasts its own WiFi network that your phone can connect to.
Start by locating the serial number on the back of your grill. You will need this number in a moment, so it is often easier to copy it into your phone’s notes app at first.
Next, open your phone’s Wi-Fi settings and look for a network name that begins with “GMG.” Select that network and enter the grill’s serial number as the password.
Once connected, open the Green Mountain Grills app. The app should detect the grill and indicate that it is connected in Point-to-Point mode. At this stage, your phone is communicating directly with the grill rather than through your home’s wireless network.
If the grill’s network does not appear, make sure the controller has finished booting completely. In some cases, you may need to reset the WiFi controller before attempting the connection again.
Step 2: Connect the Grill to Your Home Wi-Fi Network
After successfully connecting to the grill in point-to-point mode, the next step is transferring it to your home network. Open the Green Mountain Grills app and navigate to the WiFi settings section.
Here, you will see an option to switch the grill from point-to-point mode to WiFi mode. Select this option and enter your home network’s WiFi name and password.
Once you save the settings, give the grill a few moments to establish the connection. During this time, the controller will disconnect from point-to-point mode and attempt to join your wireless network.
To verify the process worked, return to your phone’s Wi-Fi settings. You should notice that the GMG network has disappeared from the available network list. This is normal and usually indicates that the grill has successfully joined your home Wi-Fi.
Now reconnect your phone to your normal home network and open the GMG app again. Tap Connect, and the app should discover the grill on the same network. If everything is configured correctly, you should now have full in-home control of your grill through WiFi mode.
Step 3: Verify the Connection and Update the Controller
Once the grill appears inside the app, take a few minutes to verify everything is working properly. Open the settings menu and confirm that temperature readings, food probe information, and grill controls are responding normally.
This is also a good time to check for firmware updates. Within the app, navigate to the Update Grill section and verify that the latest production firmware is selected. Avoid installing prototype versions unless specifically instructed by GMG support.
During the update process, the controller will begin counting upward until it eventually displays a success message. After the update completes, power the grill off and then back on.
Many owners get confused at this point because the grill may temporarily return to point-to-point mode after a firmware update. If that happens, simply reconnect to the GMG network, open the app, and repeat the process of placing the grill back into WiFi mode.
Once connected, a solid connection indicator and successful communication through the app confirm that the setup is complete.
How to Set Up Green Mountain Grill Server Mode
If you want to monitor your cook while away from home, you can also enable server mode after the grill is successfully connected to your W-Fi network.
Open the Green Mountain Grill app, connect to the grill, navigate to Settings, and select Server Mode.
The app will ask you to verify your network credentials once again before connecting the grill to GMG’s servers through your home internet connection. You’ll know that you’re in server mode when you see the right light activated on the control board.
Once the setup is complete, return to the main screen and confirm that the grill appears as connected. Unlike standard Wi-Fi mode, which only works when your phone and grill are on the same network, Server Mode allows you to check temperatures, monitor food probes, and adjust grill settings remotely.
Whether you’re running errands, watching your kid’s soccer game, or simply relaxing away from the patio, Server Mode gives you full access to the grill from virtually anywhere with an internet connection.
How to Perform a Hot Start on a Green Mountain Grill
A hot start is useful when your Green Mountain Grill loses power during a cook or shuts down unexpectedly but still contains burning pellets in the firepot. Instead of performing a complete startup cycle, a hot start allows the grill to resume operation without dumping excessive pellets into an already active fire.
To perform a hot start, first verify that the fire has not completely gone out. Turn the grill on and access the hot start function through the controller. The grill will bypass portions of the normal ignition cycle and resume operation using the remaining fire in the burn pot.
Use caution before selecting this option. If the firepot is overloaded with pellets or the grill experiences a severe temperature spike before shutting down, inspect the firepot first.
Starting a grill that already contains excess fuel can lead to rapid temperature increases and potentially trigger high-temperature alarms. Once the hot start is complete, monitor the grill closely for several minutes.
Verify that the temperature stabilizes near your set point and that pellets are feeding normally. If temperatures continue climbing uncontrollably, shut the grill down and inspect the firepot before attempting another restart.
How to Change a Green Mountain Grill From Fahrenheit to Celsius
Green Mountain Grills allow you to switch between Fahrenheit and Celsius directly from the controller. This is particularly useful if you follow recipes that use metric temperature measurements or simply prefer cooking in Celsius.
To change the temperature scale, press and hold the “Down” arrow button when the display says “Off.” The controller will switch from Fahrenheit (°F) to Celsius (°C).
Repeating the same process will switch the display back to Fahrenheit whenever needed. After making the change, verify that the displayed temperature scale matches your preference before starting a cook.
Many owners accidentally switch units and assume the grill is reading temperatures incorrectly when it is simply displaying them on a different scale.
The setting remains stored in the controller’s memory even after powering the grill off. In most cases, you only need to perform this adjustment once unless someone changes it accidentally or the controller undergoes a factory reset.
How to Set a Food Probe Alarm on a Green Mountain Grill
Green Mountain Grills allow you to set a target temperature alarm directly from the controller. Once the food reaches the selected temperature, the controller will sound an alert, letting you know it’s time to check or remove the meat.
To set the alarm, first insert the food probe into the thickest part of the meat and plug it into the appropriate probe port. Next, press the corresponding probe button on the controller. Press Probe 1 if you’re using the first probe or Probe 2 if you’re using the second probe.
The display will show the probe’s current temperature. From there, use the Up Arrow button to increase the target temperature until it reaches your desired setting. Once selected, the controller automatically saves the target temperature and begins monitoring the food.
When the meat reaches the temperature you’ve set, the grill will sound an alarm to notify you. This feature is particularly useful during long cooks because you don’t need to constantly check the temperature manually.
How to Check for Firmware Updates on a Green Mountain Grill
Firmware updates improve grill performance, add new features, and fix bugs that may affect Wi-Fi connectivity or temperature control. For that reason, checking for updates should be one of the first troubleshooting steps whenever you experience controller-related issues.
Start by connecting your grill through the Green Mountain Grills app. Once connected, open the Settings menu and select Update Grill. The app will display the firmware version currently installed on the controller and check for available updates.
If an update is available, verify that the latest production firmware is selected rather than any prototype or testing version. Confirm the installation and allow the process to finish without interruption.
During the update, the controller may display a counting sequence while the firmware is transferred and installed. When the update completes successfully, the controller will display a confirmation message.
Turn the grill off and then back on to finalize the update. After restarting, reconnect through the app and verify that all functions, including temperature controls, food probes, and Wi-Fi connectivity, are operating normally.
Keeping the firmware up to date can prevent many of the connectivity and performance issues that Green Mountain Grill owners commonly encounter.
Conclusion
Knowing how to reset Green Mountain Grill controllers can save hours of frustration. Most Wi-Fi and app issues are surprisingly easy to fix. A reset often restores communication between the grill and the app. It can also resolve many network-related problems.
Once connected, keep your firmware updated for the best performance. Server Mode is also worth setting up for remote monitoring. You can check out my guide on Green Mountain Grill igniter troubleshooting for additional fixes.
