Remington Heater Won’t Ignite [9 Easy Solutions]

The Remington heater problem that many users face is that the heater fails to ignite. This issue occurs in two forms. Sometimes, the heater motor starts up but there’s no ignition.

In that case, the possible reasons why your Remington heater won’t ignite are insufficient ground, incorrect pump pressure, dirty fuel filter or nozzle, air leak, and ruptured airline. 

In other cases, temperature limit sensor overheating, lack of electrical power, blown fuse, and improper electrical connection between the circuit board and temperature limit sensor cause the motor to not start and there’s no ignition as well.

Now, let’s take a look at the solution to these causes of heater malfunction.

Remington Heater Won’t Ignite [9 Easy Solutions]

Here’s a list of the common reasons why your Remington Torpedo heater won’t ignite and their solutions.

1. Insufficient Ground

Grounding a heater is very important. The aim of grounding a gadget is usually dual. In the event of a short circuit, the initial goal is to create a safe path for current flow. The second is to give the circuit a true “zero voltage” reference. An issue with the grounding can cause your heater to not ignite.

Solution:

Check to see if there is any spark present at the spark plug. If not, the grounding is insufficient. Inspect the wires between the ignitor and the spark plug. Tighten any loose connections you find. Ensure that the ground wire is securely attached to the heater’s body.

Replace the spark plug if it is rusted or damaged. Adjust the spark plug gap to 0.140 inches (3.5mm). Check for a malfunctioning ignitor at an Authorized Service Center (Transformer). Parts can be obtained from any Authorized Service Center or directly from Pinnacle.

2. Incorrect Pump Pressure

Every heater unit comes with a specified pump pressure that is needed for the heater to run seamlessly. If your heater is getting an incorrect pump pressure that can cause it to not ignite.

Solution:

Check the manufacturer’s specifications listed in the User’s Manual. You’ll need to adjust the pump pressure to that.

3. Dirty Fuel Filter or Nozzle

Another possible reason why your Remington heater won’t ignite is that you’ve let too much dirt accumulate in the fuel filter or nozzle.

Solution:

A clogged fuel filter or nozzle might prevent fuel from reaching the spark plug. It is good practice to clean or change the nozzle at least once during the heating season while fuel filters need to be cleaned twice.

But if the fuel in your fuel tank is contaminated for any reason, you should immediately clean the fuel filter and nozzle. 

Not following this guideline can increase the risk of your heater not igniting. Proper maintenance can add years to your heater.

To clean the nozzle, blow compressed air through the nozzle front to remove dirt. To dislodge any particles, it may be necessary to soak the nozzle in clean 1-K kerosene. You can also clean the fuel filter this way by rinsing it in clean 1-K kerosene.

4. Air Leak

An air leak can be causing your heater’s problem. Signs that point to air leaks are

• An increased energy bill
• Your home getting dusty more frequently
• Your heater’s ductwork is old

Solution:

The flow of fuel to the burner head will be obstructed if there is an air leak. Ensure a full fuel bowl and that there’s no air allowed into the fuel system. Fuel distribution may be irregular if the fuel system is pulling air. For the heater to ignite, the fuel has to be sprayed in a constant and automatic pattern.

A damaged and cracked end filter cover can also be behind this problem. You may have to replace the end filter cover to fix this issue.

5. Ruptured Airline

A ruptured airline can be behind your Remington Torpedo heater not igniting.

Solution:

The flow of fuel to the burner head can stop because of a disconnected or ruptured airline. Make sure that the airline is tightly attached and not damaged in any way that can impede airflow. You’ll need to replace the airline if necessary.

6. Temperature Limit Sensor Overheating

The temperature limit sensor continuously evaluates the heater’s temperature. There’s a safety mechanism in Remington heaters to prevent house fires.

When the mechanism notices the temperature goes above a certain level, the system allows the heater turns off instantly. This limit is set by the manufacturer. This safety mechanism can be your heater has turned off and won’t ignite. 

Solution:

You’ll need to reset the heater to fix this issue. Here’s how you reset a Remington heater:

• Turn the power switch off. 
• For 10 minutes, allow the heater to cool down.
• Turn the power back on.

7. Lack of Electrical Power

Without power, your heater won’t run and ignite. This can happen due to a brownout or blackout situation.

Solution:

Check to see if the heater is plugged in correctly and if the power is on. Inspect other appliances at home to see if there’s an outage. You’ll have to wait for power to be restored in that case.

8. Blown Fuse

Electrical overload can trip the fuse in your heater and turn it off. Another common reason behind blown heater fuses is poor airflow. Insufficient airflow can be caused by faulty blowers, dirt build-up in the air filter, and other heater parts.

Solution:

You’ll need to replace the heater fuse after locating it in the PC board. You can watch the tutorial to change the fuse.

9. Incorrectly Wired Heater

Improper electrical connection between the circuit board and temperature limit sensor is also a cause behind your heater won’t run.

Solution:

Turn off the power to the heater before doing anything. Check the wiring diagram in your owner’s manual and cross-examine it with your heater’s wire connections. Fix any improperly wired connections.

FAQ

Why won’t my kerosene heater shut off?

When the kerosene heater isn’t shutting off because the wick won’t drop, it’s most likely due to tar and carbon build-up from using polluted kerosene or burning the wick too low. As a hardened wick is more difficult to maneuver between the wick adjuster and the primary air tube, your heater flame stays on.

Why is my oil burner not firing up?

You should check the following thing-

• Your thermostat temperature and timer settings
• Power supply to the boiler
• Insufficient fuel in the tank

Can mineral spirits be used in a kerosene heater?

In a kerosene lantern, you can use 100 percent mineral spirits or low-odor mineral spirits. The vapor pressure is the same in both cases.

How many times can I hit the reset button on my furnace?

Hitting the reset button more than twice isn’t a good idea. The process of resetting is that oil will get pumped to the burner chamber. This oil will keep accumulating if there is no ignition. So, when you’ll turn on the heater, the ignition will be explosive. So if the reset button isn’t working properly, don’t keep pressing it. Get a professional to take a look.

How long does it take for a furnace to reset?

Generally, you should be able to reset your furnace in under 10 minutes. The process is relatively simple.

Conclusion

Hopefully, you have gotten a clear idea of why your Remington heater won’t ignite from this article. If you have any queries, we’d love to help you out. Leave us a comment below and we’ll get back to you soon with our best answers.

Cheers! And enjoy the warm air.