Pacific Energy Super 27 Problems [7 Easy Solution]

Low heat output, too much creosote build-up, the stove won’t burn, the furnace won’t turn on, dirty glass, short burn times, and smoke rollout when loading is the major Pacific Energy Super 27 problems.

Here, we will explore the detailed causes and solutions of each of the above issues.

So, go through our comprehensive and step-by-step guide and fix your Pacific Energy Super 27 wood stove issues by yourself.

Pacific Energy Super 27 Problems [7 Easy Solution]

Pacific Energy Super 27’s major issues and their simple solutions are the following:

1. Low Heat Output

Inadequate or poor heat output from the Pacific Energy Super 27 le is one of the major problems of this wood stove.

The Pacific Energy Super 27 wood stove’s successful fire and perfect heat output depend on several factors. However, the leading causes of producing low heat are:

• Using wet or excessive moisture wood for burning 
• The stove fails to draw sufficient fuel
• Too small fire
• Low draft or poor airflow
• Close or too much open air vents
• Secondary combustion fails to occur
• Incorrectly lighting and building the fire
• Excessive ash build-up

Solution:

The easy solutions to all the above problems are the following:

• Use perfectly dry and seasoned wood for burning
• Make sure your wood stove is drawing sufficient fuel
• Ensure that the fire is not small
• Check the air vents and make sure it is not very much open or fully closed
• Ensure sufficient air supply
• Make sure secondary combustion is occurring properly
• Frequently clean the chimney and avoid the ash build-up

2. Excessive Creosote Buildup

Creosote is one kind of soot that accumulates on the chimney when you use your Pacific Energy Super 27 wood stove.

Excessive creosote build-up in your Pacific Energy Super 27 blower is a major problem as it causes chimney fires. Several factors combinedly lead to building up too much creosote in your wood stove. Those factors are:

• The restricted air supply in the chimney
• Making fire using the wet or unseasoned wood
• Compared to the average temperature, the chimney’s temperature is cooler
• Dumper or air control’s turning down
• Lower draft

Solution:

When your wood stove exposes heat to an excessive amount, the creosote builds in chimneys. As it can cause fire thus, you should immediately solve this problem. The solutions to this issue are:

• Ensure adequate air supply in your chimney
• Use only dry and adequately seasoned wood for making fire
• Inspect the temperature and make sure the chimney’s temperature is higher than the normal temperature
• Until the wood is appropriately charred and there is adequate coal, avoid turning down the damper

3. Stove Won’t Burn

One of the major problems with the Pacific Energy Super 27 wood stove is that the furnace stops burning.

The wood stove won’t ignite mainly because of the defective or broken Pacific Energy Super 27 parts. However, the following factors are also responsible for this crisis.

• Blocked combustion air supply
• Restricted or plugged chimney
• Unsuitable or oversized chimney
• Too air-tight room
• Dirty chimney
• Closed damper
• Too warm or windy weather

Solution:

You can combat your Pacific Energy Super 27 won’t ignite or burn issue by following the solutions below: 

• Check the combustion air supply and make sure it is not blocked
• Ensure the chimney is not restricted and adequately clean your dirty chimney
• Make sure your stove is getting proper air supply
• Avoid using your wood stove in too warm or windy weather

4. The Stove Won’t Turn On

Another problem with the Pacific Energy Super 27 wood stove is that you may fail to start a fire on your wood stove as it is not turning on. The concerning factors responsible for this trouble are:

• Poor wood supply or inadequately seasoned wood
• Lack of enough air supply
• The draft air or combustion air is moving up the chimney
• Dirty chimney
• Closed vents
• Excessive pressure in chimney tube
• Stove’s open damper handle

Solution:

If your Pacific Energy wood stove fails to turn on, you should inspect which culprit is creating the problem and then go with the following solutions:

• Supply wood adequately in your stove and use properly seasoned and dry wood
• Ensure adequate air supply in the stove
• Properly clean the dirty chimney and make sure the combustion air is not moving up to the chimney
• Check the vents and ensure it is not too much close or open
• Avoid creating too much pressure in the chimney tube
• Make sure the stove’s damper handle is close

5. Dirty Glass

Pacific Energy Super 27 wood stove’s dirty glass is one of the major problems users often face. Due to the dirty glass, you may fail to view the fire clearly. The causes of it are:

• Using wet or unseasoned wood for burning
• Frequent turning down of damper or air control
• Too low draft or poor airflow
• The unadjusted diameter or chimney height
• Leaked door gasket

Solution:

Before reloading your stove to start burning, first clean the stove’s dirty glass properly. Make sure your stove is cool enough, and then use the built-in air wash for cleaning it. The other solutions are:

• Use adequately seasoned and dry wood for burning
• Until the wood is appropriately charred and there is adequate coal, don’t turn down the damper or air control
• Ensure proper airflow and for combustion, provide the outside air
• Properly adjust the diameter or chimney height
• Check the latch and replace the leaking door gasket

6. Short Burn Times

After starting burning, the fire in your wood stove won’t stay lit for maximum times, or the short burn times is another problem of the Pacific Energy Super 27 le. The reasons behind this are:

• The tall chimney causes a high draft
• Cold weather
• The burn cycle parts don’t include the charcoal phase
• Too far open-air vents
• Damaged stove or leakage in the stove
• Too small logs
• Open stove door

Solution:

Follow the easy solutions below to solve the above troubles:

• Check your chimney’s height and make sure it is not causing high draft due to excessive height
• Avoid using your wood stove in freezing or cold weather
• Make sure the charcoal phase is included in the burn cycle
• Inspect the vent and keep it close
• Repair or replace the leaked or damaged stove
• Ensure the stove’s door is close
• Use adequately sized logs

7. Smoke Rollout When Loading

During loading, the smoke in your Pacific Energy Super 27 wood stove rolls out, which is another problem with this stove. The accountable factors for it are:

• Smoldering fire
• Closed primary air shutter
• Restrictive venting system
• Poorly burning of woods

Solution:

To solve the above issues, follow the solutions below:

• Use dry and properly seasoned wood to reduce smoldering fire
• Ensure that the primary air shutter is open
• To avoid the restrictive venting system, replace the inside chimney with outside
• Make sure the wood is burning perfectly

FAQ:

Why does smoke come out of my wood burner when I open the door?

Cold chimney, bad draft, obstructed or clogged chimney and the wind-induced downdraft are mainly responsible for the smoke coming out of your wood burner when you open the door.

How can I get my wood stove to draft better?

Your wood stove’s draft will go better and upward if you start your cold wood stove with a fast and hot fire. Now make sure the fire is improving, and there is proper airflow. Next, warm the stove’s chimney flue. Finally, replace the stove’s lost air by supplying enough air.

Why is my wood stove not drawing?

Too cold fuel, dirty chimney, too cool stove, excessive air-tight house or room are mainly responsible for which your wood stove is not drawing.

Conclusion

So, now you know what are the common Pacific Energy Super 27 problems and their solutions.

Hopefully, from now, whenever you face any of the trouble mentioned above with your Pacific Energy Super 27 stove, you can fix it by yourself.

But, if you fail to resolve your issue, don’t be hopeless. Comment, and we will provide the solution ASAP.