When your Masterbuilt smoker won’t turn on and the display is blank, it can be because of a tripped GFCI breaker, broken heating element, or a faulty control panel. There is no need to panic in case you are facing this trouble.
Follow our Masterbuilt electric smoker no power troubleshooting guide and fix your smoker ASAP.
Table of Contents
- Masterbuilt Electric Smoker No Power [3 Easy Solution]
- 1. Tripped GFCI Breaker
- 2. Broken Heating Element
- 3. Faulty Control Panel
- FAQ:
- How often should you add wood chips to an electric smoker?
- Do electric smokers give off smoke?
- Do you put meat directly on rack in an electric smoker?
- Why is my electric smoker shocking?
- How open should the vent be on the electric smoker?
- Conclusion
Masterbuilt Electric Smoker No Power [3 Easy Solution]
In this section of our Masterbuilt smoker troubleshooting guide, we’ll take an in-depth look at each problem and provide you with the simplest solutions.
1. Tripped GFCI Breaker
You may notice your Masterbuilt electric smoker tripping the GFCI breaker. The circuit breaker will trip if your smoker is using more current than is safe, preventing an electrical fire.
The majority of high-end electric smokers are built with low power and amperage consumption in mind.
An average-sized smoker needs about 750 watts. Even so, you may have too many appliances plugged in the same circuit causing it to trip.
Solution:
To see if the breaker is tripped, try plugging in another appliance to the outlet and see if it runs.
In case the other appliance isn’t running you can be sure that the circuit breaker has tripped. Fix the circuit by taking the following actions-
- Locate the breaker box in your residence. It could be in the basement, the laundry room, the garage, the hallway, or the utility closet..
- You’ll discover rows of individual circuit breakers when you open the door of your breaker box. If the breaker box feels hot, you need to be cautious. Wait a few minutes to see whether it is cooling. It is best to call in a professional in case the circuit breaker is still unusually hot.
- Determine which circuit breaker was triggered. Two or three settings are available on circuit breaker switches. Those who have two options will be turned on or off. There are three positions on those with three settings: “on,” “off,” and “neutral” (centre).
- Switch the tripped breaker to the “on” position if it is currently in the “off” position. Turn it off and then back on if it’s in the “neutral” position. Please wait a moment. The breaker has been reset if the switch stays in the “on” position.
If the GFCI circuit trips every time you plug in the smoker, try connecting it into a new outlet to see if the problem persists.
2. Broken Heating Element
One of the reasons that your smoker may not be getting power can be that your smoker’s heating element is broken and causing the circuit to trip. To fix this issue, you’ll need to repair or replace the smoker heating element.
Solution:
Follow the steps given below to replace your old heating element with a new one.
Step 1:
Get to the back of your smoker. Close to the bottom, you’ll find a plate screwed in. First, you’ll need to take out the six screws.
After you remove the panel, two leads should be visible to you. Now you will have to probably use a razor blade and cut off the heat shrink. Then, all you need to do is just unplug the leads.
Step 2:
This is where the heating element is screwed on. The middle screw is for the ground. The two screws on the sides secure the heating element. Unscrew all three.
Now you can pull the heating element out. At the inside of the smoker, the heating element is situated below the smoke tray.
You’ll need to remove the screws on the smoke tray and take it out to access the heating element. Take out the heating element.
Step 3:
You want to put the gasket onto your new heating element. Position the ground wire now just at an angle, put the heating element through from the back.
Then just screw in the heating element. You don’t want to tighten it up yet. Roughly screw it in.
Step 4:
Focus on the ground wire in the middle. It might have moved its position by now.
All you do is take your screwdriver or something small just to reposition it. Now you can tighten the screws and secure the heating element.
Step 5:
Go ahead and put the insulated rubber housing back in. Reconnect the two wires to the heating element. Technically, there is no orientation.
You can connect the wires to the leads in any combination. Test your heating element by powering the smoker. If it’s fine, reassemble the other parts carefully.
3. Faulty Control Panel
A faulty control panel can also be why your Masterbuilt smoker isn’t getting power.
Solution:
There could be a number of reasons why your Masterbuilt control panel isn’t functioning properly. If the problem is due to physical damage, you’ll need to contact the manufacturer for Masterbuilt smoker control panel replacement.
However, if your control panel appears to be in good physical condition, the following suggestions should be helpful. You’ll require-
- WD-40
- Compressed air can
- Phillips head screwdriver
Step 1:
Remove the screws from the panel that is fastened to the smokers with the head screws. Pull the controller carefully after that.
Remove the clips from it as well. After that, you’ll notice four more head screws, which you should unscrew as well. After that, the control buttons will appear.
Step 2:
Place the buttons on a paper towel and gently press them down. It’s time to spray your Masterbuilt smoker control panel with WD-40.
When you’re finished, take out the compressed oxygen and re-dry them. The wind blows over the clips, keeping them tethered to the wire.
Step 3:
To construct the control panel, repeat the method in reverse. You’ve cleared out the clutter on the inside.
So it’s safe to assume that the Masterbuilt smoker beeping problem has been rectified and that the panel will begin to function.
FAQ:
How often should you add wood chips to an electric smoker?
1 cup of wood chips will typically last 4 to 5 hours. Continue to keep an eye on the smoke without opening the smoker door. Until the cooking period is over, add a handful of wood chips every 4 hours or so.
Do electric smokers give off smoke?
Electric smokers tend to create the least amount of smoke of any smoker fuel type. This is due to the fact that it is the only heating source that does not require the presence of a flame or combustion.
Do you put meat directly on rack in an electric smoker?
These racks can be used to hold cast iron skillets in which your food can roast, or they can be used to hold meat directly on them. Stainless steel grill racks are standard on most electric smokers.
Why is my electric smoker shocking?
Exposed wire, static shock, water in the smoker, and an inadvertent short circuit established someplace on the smoker’s body are all possible reasons for an electric shock from your electric smoker.
How open should the vent be on the electric smoker?
When applying smoke to your meat, it’s recommended to leave the vent fully open as a matter of thumb. You may avoid creosote buildup on your meat by leaving the vent totally open.
Conclusion
Hopefully, with the help of our Masterbuilt electric smoker no power troubleshooting guide, you can get your smoker to work as smoothly as butter.
In case you have more questions about why your smoker won’t heat up, you can leave us a comment below. You’ll hear from us soon.
No power from the control panel.I replaced with another control panel same problem
Hi Levon
To solve the control panel issue, follow our solution guide on Masterbuilt Smoker Control Panel Not Working.
Hopefully, you will get the solution.
Wish you all the best.